powerex, inc., 200 e. hillis street, youngwood, pennsylvania 15697-1800 (724) 925-7272 hybrid ic igbt gate driver VLA513-01 rev. 04/07 description: VLA513-01 is a hybrid integrated circuit designed for driving igbt modules. this device operates as an isolation amplifer for these modules and provides the required electrical isolation between the input and output with an opto- coupler. features: propagation delay time: 0.2 s (typical) output is 5a maximum two supply drive (v cc : 15 volts, v ee : -10 volts) sip outline allows more space on mounting area electrical isolation voltage between input and output (2500 v rms for 1 minute) ttl compatible input application: to drive igbt modules for welding, induction heating, or inverters. recommended igbt modules: nfh series igbts C v ces = 600v & 1200v up to 200a class (f: up to 60khz), 400a class (f: up to 30khz) nf series igbts C v ces = 600v up to 600a v ces = 1200v up to 400a outline drawing and circuit diagram 1 8 a b j c f g d d h e k interface opto coupler 5 pin: nc 180 ? v cc v o v ee 2 1 6 7 8 l dimensions inches millimeters a 1.85 max. 47.0 max. b 1.063 max. 27.0 max. c 0.28 max. 7.0 max. d 0.59 max. 15.0 max. e 0.10 2.54 f 0.216 max. 5.5 max. g 0.08 max. 2.0 max. h 0.70 17.78 j 0.180.06 4.51.5 k 0.03 0.75 l 0.02 0.5
VLA513-01 hybrid ic igbt gate driver powerex, inc., 200 e. hillis street, youngwood, pennsylvania 15697-1800 (724) 925-7272 rev. 04/07 absolute maximum ratings, t a = 25c unless otherwise specifed characteristics symbol VLA513-01 units supply voltage, dc v cc 18 volts v ee -12 volts input signal voltage (applied between pin 1 - 2, 50% duty cycle, pulse width 1ms) v i -1 ~ 7 volts output voltage (when the output voltage is "h") v o v cc volts output current i ohp -5 amperes (pulse width 2s, f 20khz) i olp 5 amperes isolation voltage (sine wave voltage 60hz, for 1 minute) v iso 2500 v rms case temperature1 (surface temperature opto-coupler location)*** t c1 85 c operating temperature (no condensation allowable) t opr -20 to 70 c storage temperature (no condensation allowable) t stg -25 to 100* c *differs from temperature cycle condition. electrical and mechanical characteristics, t a = 25c unless otherwise specifed, v cc = 15v, v ee = -10v characteristics symbol test conditions min. typ. max. units supply voltage v cc recommended range 14 15 volts v ee recommended range -5 -8 -12 volts pull-up voltage on input side v in recommended range 4.75 5 5.25 volts "h" input current i ih recommended range 9.5 10.0 14.0 ma switching frequency f recommended range 60 khz gate resistance r g recommended range 2 w "h" input current i ih v in = 5v 10 ma "h" output voltage v oh 13 14 volts "l" output voltage v ol -8 -9 volts "l-h" propagation time t plh i ih = 16ma 0.1 0.2 0.5 s "l-h" rise time t r i ih = 16ma 0.3 1 s "h-l" propagation time t phl i ih = 16ma 0.05 0.2 0.5 s "h-l" fall time t f i ih = 16ma 0.3 1 s
VLA513-01 hybrid ic igbt gate driver powerex, inc., 200 e. hillis street, youngwood, pennsylvania 15697-1800 (724) 925-7272 rev. 04/07 t plh t phl t plh t phl 0.7 0.5 0.6 0.2 0.1 0.4 0.3 0 2 0 6 0 40 80 ambient tempera ture, t a , (c ) pr op ag at ion dela y time l-h, t plh , (s) pr op ag at ion dela y time h-l , t ph l , (s) t plh , t phl vs. t a chara cteristics (typical) 0 0.7 0.6 0.5 0.2 0.4 0.1 0.3 3 4 6 5 7 input signal vo lt ag e, v i , (v ol ts ) pr op ag at ion dela y time l- h , t plh , (s) pr op ag at ion dela y time h- l , t ph l , (s) t plh , t phl vs. v i chara cteristics (typical) 0 v cc = 15 v v ee = -10 v r g = 3 w v in = 5v load: cm400du-24nfh v cc = 15 v v ee = -10 v r g = 3 w t a = 25 c load: cm400du-24nfh r g = 2 w or more * 5 4 3 0 1 2 0 2 0 4 0 6 0 8 0 100 ambient tempera ture, t a , ( c) tot al po wer dissip at ion, p t , (w at ts ) p t vs. t a (maximum ra ting ) 18 12 15 9 3 6 0 5 10 20 25 30 15 35 suppl y vo lt ag e, (v cc + i v ee i ), (v ol ts ) dissip at ion current , i cc , (ma) i cc vs. (v cc + | v ee | ) chara cteristics (typical) 0 t a = 25 c * the f ollo wing number ical ex pression must be satisfied pt > (v cc + i v ee i ) * {(q 1 + i q 2 i ) * f + i cc } q 1 : gate charge on plus bias q 2 : gate charge on minus bias f: switching frequency i cc : constant dissipation current of dr iv er ref er to i cc vs . (v cc + iv ee i) character istics v cc v cc = 15v v ee = -10v r g = 3 ? r g cm200du-24nfh 220 f 220 f v in + + v ee 5v 7 8 1 2 5 6 VLA513-01 notes: (1) power supply decoupling capacitors should be connected as close as possible to the pins of the gate driver. (2) power supply decoupling capacitors should be good quality, low esr types. (3) printed circuit layout should minimize wiring lengths and utilize shielding layers to suppress noise. v i v o 90% 50% 10% t r t f t plh t ph l switching time definitions application circuit switching time defnitions
|
